🇺🇸English

MATSON METAL / ENGINEERING TOOLS

Surface Roughness Converter

Convert Ra between µm and µin, check ISO N roughness grades, and view estimated Rz values for machined surfaces.

Input

Enter a roughness value

Input parameter
µm

Enter a positive Ra value.

Common surface roughness values

Conversion results

Live
Ra Metric
1.6 µm
Ra Imperial
62.99 µin
ISO Roughness Grade
N7
Estimated Rz
6.4–11.2 µm

Estimated Rz only. Ra and Rz describe different surface profile characteristics. The estimated Rz value is for general reference only and must not replace the roughness requirement specified on an engineering drawing.

REFERENCE TABLE

Surface Roughness Conversion Chart

ISO N grades correspond to standard Ra values. Imperial values below use the exact unit relationship 1 µm = 39.3701 µin.

N GradeRa µmRa µin
N10.0250.98
N20.051.97
N30.13.94
N40.27.87
N50.415.75
N60.831.50
N71.662.99
N83.2125.98
N96.3248.03
N1012.5492.13
N1125984.25
N12501,968.51

SURFACE PARAMETERS

What Is Ra Surface Roughness?

Ra is the arithmetic average of the absolute height deviations measured along a surface profile. It is one of the most commonly specified roughness parameters on engineering drawings because it gives a practical average value for comparing machined surfaces.

Ra does not describe every peak, valley, spacing, or functional behavior of a surface. A complete surface requirement may also need a cutoff length, evaluation length, machining direction, or an additional roughness parameter.

ENGINEERING NOTE

Ra vs Rz: What Is the Difference?

Ra represents an arithmetic average across the measured profile. Rz represents peak-to-valley behavior based on the applicable measurement standard. Two surfaces can have the same Ra value but different Rz values and different functional behavior.

There is no universal exact conversion between Ra and Rz. This calculator shows an engineering reference range of approximately 4–7 × Ra and labels it Estimated Rz.

Machined metal coupons with turning, milling, grinding and polished surface finishes
Representative machining textures shown for visual context. Roughness must be verified by measurement.

GENERAL REFERENCE

Common Surface Roughness for CNC Machining

Actual results depend on the material, machine condition, tooling, cutting parameters, part geometry, and measurement method. The ranges below are typical references, not guaranteed process limits.

Machining ProcessTypical Ra Range
Rough Turning3.2–12.5 µm
Finish Turning0.8–3.2 µm
Rough Milling3.2–12.5 µm
Finish Milling0.8–3.2 µm
Grinding0.2–1.6 µm
Polishing0.05–0.4 µm

PART DESIGN

How to Choose Surface Roughness for Machined Parts

Choose the finish from the function of each surface. Applying one tight roughness requirement to an entire part can add machining time and inspection cost without improving performance.

A smoother surface is not always better. Stricter values usually require additional passes, more stable tooling, grinding, polishing, or more inspection.

  • FrictionContact behavior and movement
  • WearSurface durability under repeated contact
  • SealingLeak paths and gasket performance
  • CoatingAdhesion and final appearance
  • FitBearing, sliding, and mating surfaces
  • CostMachining time and finishing operations

FAQ

Surface Roughness Questions

What is Ra surface roughness?

Ra is the arithmetic average of the absolute deviations along a measured surface profile. It is commonly specified in micrometers (µm) or microinches (µin).

How do you convert Ra µm to µin?

Multiply the Ra value in micrometers by 39.3701. For example, 1.6 µm × 39.3701 = 62.99 µin.

Is Ra the same as Rz?

No. Ra is an average roughness value, while Rz describes peak-to-valley characteristics according to the applicable measurement standard.

Can Ra be converted directly to Rz?

No exact universal conversion exists. A range such as 4–7 × Ra may be used for general engineering reference, but the drawing requirement must control.

What does N7 surface finish mean?

N7 corresponds to Ra 1.6 µm, which is approximately 62.99 µin.

What surface roughness can CNC machining achieve?

The achievable finish depends on the process, material, machine, tooling, geometry, and inspection method. General references range from rough machining above Ra 3.2 µm to grinding or polishing below Ra 0.8 µm, but every part should be reviewed individually.

CUSTOM MANUFACTURING SUPPORT

Need Help With a CNC Machined Part?

MATSON METAL supports custom CNC machining based on your drawings, material, tolerance, surface finish, and inspection requirements.

View CNC Machining Services